Fedora Linux Support Community & Resources Center
  #1  
Old 13th March 2010, 02:00 AM
STEVE555 Offline
Registered User
 
Join Date: Nov 2004
Posts: 104
linuxfedorafirefox
Wierd Nouveau Error with Kernel-2.6.34.0.10-rc1.git0 - 2.6.34-rc1

Hi everyone,
I get a weird error message that locks up the 2.6.34.0.10-rc1.git0 - 2.6.34-rc1 kernel if I have AGP mode 8x with side-banding on in my bios settings.

I've taken some steps if it will boot with different bios settings for my motherboard.
I first tried AGP 4x,and that booted fine to the dektop.
I then tried AGP 8x with no side-band on and that booted fine as well.
I tried again with AGP 8x and side-banding on but I removed rhgb quiet from the kernel parameters and pressed b to boot and that booted fine as well.

The error occurs when I have AGP8x with sidebanding and I don't do anything to the kernel parameters.
The kernel runs a load of messages,but stops at the end of this:
Code:
[drm] nouveau 0000:01:00.0: unknown type, using 0xff
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xE754
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xEBFC
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xF26A
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xF3C7
[drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xF469
[TTM] Zone  kernel: Available graphics memory: 431346 kiB.
[TTM] Zone highmem: Available graphics memory: 1027286 kiB.
[drm] nouveau 0000:01:00.0: 256 MiB VRAM
agpgart-sis 0000:00:00.0: AGP 3.0 bridge
agpgart: modprobe tried to set rate=x12. Setting to AGP3 x8 mode.
It seems the kernel thinks I have a PCI-Express slot
When I get that error message,I have to do a hard reset,and boot into my previous kernel(2.6.33-1.fc13.i686),but I don't have any problems with that one.My Graphics Card is a
Code:
1:00.0 VGA compatible controller: nVidia Corporation NV40 [GeForce 6800 GT] (rev a1) (prog-if 00 [VGA controller])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at ce000000 (32-bit, non-prefetchable) [size=16M]
        Region 1: Memory at b0000000 (32-bit, prefetchable) [size=256M]
        Region 2: Memory at cd000000 (32-bit, non-prefetchable) [size=16M]
        Expansion ROM at cfee0000 [disabled] [size=128K]
        Capabilities: <access denied>
        Kernel driver in use: nouveau
        Kernel modules: nouveau, nvidiafb
My monitor is a ADI Microscan G1000.I compile the latest DRM,Nouveau Kernel Modules,Mesa and the xf86-video-nouveau driver all from the git repositories.I'll attach the relevant files to this post.
Regards,
STEVE555
Attached Files
File Type: txt dmesg.old.txt (29.2 KB, 88 views)
File Type: txt dmesg.txt (26.8 KB, 88 views)
File Type: log Xorg.0.log (25.0 KB, 132 views)
File Type: conf xorg.conf (2.2 KB, 136 views)
  #2  
Old 13th March 2010, 04:29 AM
leigh123linux Online
Retired Administrator
 
Join Date: Oct 2006
Posts: 22,112
linuxfedorafirefox
Re: Wierd Nouveau Error with Kernel-2.6.34.0.10-rc1.git0 - 2.6.34-rc1

I wasn't aware that AGP had a X12 mode


Code:
agpgart-sis 0000:00:00.0: AGP 3.0 bridge
agpgart: modprobe tried to set rate=x12. Setting to AGP3 x8 mode.
 

Tags
error, kernel010rc1git0, nouveau, rc1, wierd

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
kernel-2.6.33-0.40.rc7.git0.fc13.x86_64 won't boot CiaW Fedora 13 Development Branch 3 13th February 2010 03:16 AM
rawhide kernel 2.6.33-0.40.rc7.git0 64bit has high interrupt rate marko Fedora 13 Development Branch 1 10th February 2010 05:28 AM
2.6.33-0.36.rc7.git0.fc13.i686.PAE kernel is working. :) diamond_ramsey Fedora 13 Development Branch 1 8th February 2010 04:32 AM
2.6.33-0.25.rc6.git0.fc13.i686.PAE kernel is working like a champ. :rolleyes: diamond_ramsey Fedora 13 Development Branch 2 1st February 2010 10:46 PM
Enabling kernel-mode-setting through Nouveau.... RaiCoss Alpha, Beta & Snapshots Discussions (Fedora 11 Only) 9 17th April 2009 03:11 AM


Current GMT-time: 20:56 (Sunday, 20-04-2014)

TopSubscribe to XML RSS for all Threads in all ForumsFedoraForumDotOrg Archive
logo

All trademarks, and forum posts in this site are property of their respective owner(s).
FedoraForum.org is privately owned and is not directly sponsored by the Fedora Project or Red Hat, Inc.

Privacy Policy | Term of Use | Posting Guidelines | Archive | Contact Us | Founding Members

Powered by vBulletin® Copyright ©2000 - 2012, vBulletin Solutions, Inc.

FedoraForum is Powered by RedHat